Crucial MTFDDAK120MBB-1AE1ZA Datenblatt

M500DC 2.5-Inch SATA NAND Flash SSDMTFDDAK120MBB-1AE1ZABYY, MTFDDAK240MBB-1AE1ZABYY,MTFDDAK480MBB-1AE1ZABYY, MTFDDAK800MBB-1AE1ZABYYFeatures• Micron®

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description76 – – – Serial ATA capabilities15

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description79 – – – Serial ATA features are en

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description82 – – – Command set is supported15

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description84 – – – Command set/feature-suppor

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description86 – – – Command set/feature is ena

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description88 – – 0b Ultra DMA modes15 – 0b Re

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description93 – – – Shall be 0000h for SATA de

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description96 – (O)V 0000h Streaming transfer

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description119 – – – Commands and feature sets

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description128 – – – Security status15–9 F 000

Part Numbering InformationMicron’s M500DC SSD is available in different configurations and densities. Visit micron.com for a list of valid partnumbers

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description206 – – – SCT command transport15–1

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description222 – – – Transport major revision

CommandsTable 6: Supported ATA Command SetSee ATA-8 standard for command detailsCommand Name Command Code (hex)CHECK POWER MODE 98h or E5hDATA SET MAN

Table 6: Supported ATA Command Set (Continued)See ATA-8 standard for command detailsCommand Name Command Code (hex)SECURITY FREEZE LOCK F5hSECURITY SE

PerformanceMeasured performance can vary for a number of reasons. The major factors affectingdrive performance are the density of the drive and the in

Mean Time to FailureMean time to failure (MTTF) for the SSD can be predicted based on the component reli-ability data using the methods referenced in

Electrical CharacteristicsStresses greater than those listed may cause permanent damage to the device. This is astress rating only, and functional ope

ComplianceMicron SSDs comply with the following:• RoHS• CE (Europe): EN55022, 2006 + A1:2007 and EN55024, 1998 + A1:2001 + A2:2003• FCC: CFR Title 47,

Package DimensionsFigure 4: 2.5-Inch Package – 7mm 100.50mm/3.957infor reference only0.30mm/0.012infor reference only14.00mm0.551in90.60mm3.567in100.2

References• Serial ATA: High-speed serialized AT attachment, Serial ATA working group, availableat www.sata-io.org• SATA 3.1 GOLD• ATA-8 Rev. 4M500DC

General DescriptionMicron’s M500DC solid state drive (SSD) uses a single-chip controller with a SATA inter-face on the system side and n-channels of M

Revision HistoryRev. E – 8/14• Updated device ID values• Updated Idle Average values in Table 11: SATA Power ConsumptionRev. D – 4/14• Status changed

Logical Block Address ConfigurationThe drive is set to report the number of logical block addresses (LBA) that will ensuresufficient storage space for

Interface ConnectorsThe SATA signal segment interface cable has four conductors and three ground connec-tions. As shown in Package Dimensions, the cab

Figure 3: SSD Interface Connections PowersegmentP1 S1SignalsegmentDevice IDTable 5: Identify DeviceSee Note 1 for setting definitionsWord Bit(s) Setti

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description48 – – – Trusted Computing feature

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description59 15 F 1b 1 = The BLOCK ERASE EXT

Table 5: Identify Device (Continued)See Note 1 for setting definitionsWord Bit(s) Setting Default Value Description69 – F – Additional supported15 F 0